前のページに戻ります
UMOP
O-Seal Pipe Thread Connector

カテゴリー

  • Instruments | Tube Fittings | Tube to SAE/MS O-Ring Seal
  • Dimensions
  • How To Order
  • Tubing & Pipe end Thread Information
  • Features

Dimensions


 

Connects Fractional Tube to Female NPT Thread
Part No.Tube OD
T
P
(NPT)
Dimensions (mm)
E
Min.
hHFII1L
inchmminchmminchmm
UMOS-0202N1/83.171/82.33/419.057/1611.1112.726.27.132.8
UMOS-0402N1/46.351/84.83/419.059/1614.2815.227.77.135.1
UMOS-0404N1/46.351/44.815/1623.819/1614.2815.231.09.738.4
UMOS-0604N3/89.521/47.115/1623.8111/1617.4616.832.59.739.9
UMOS-0606N3/89.523/87.11-1/828.5711/1617.4616.834.010.441.4
UMOS-0608N3/89.521/27.11-5/1633.3311/1617.4616.839.613.547.0
UMOS-0808N1/212.701/210.41-5/1633.337/822.2222.939.613.549.8
ISO Tapered threads are available for all fractional UMBT. To order, add “R” as a suffix instead of “N”.
Dimensions are for reference only and are subject to change without prior notice. E is minimum opening. F and L are typical finger tight.


O-Seal Fittings Information


Application 

UNILOK O-Seal fittings can be directly installed into the existing pipe threads or straight thread ports. As they have short thread length, thread interference does not occur whereas it is common on tapered thread and the leak tightness is obtained by O-ring additionally. The standard Buna-N O-ring has a precision groove, the groove provides anti-extrusion of O-ring at high pressure and controlled squeeze for vacuum tight sealing. To attain a leak tight installation, smooth flat surface perpendicular to the axis of the threads is required. 


Installation Instructions 

1. Hand tighten UNILOK O-Seal fittings into the port until the O-ring compresses on the port. 

2. Wrench-tighten the fittings lightly until the fittings contacts the face of port. Note : The fitting body is always held by back-up wrench when installing or disassembling tubing to or from UNILOK port end to get a proper sealing. 


Mounting Dimensions of O-Seal Fittings 

 

Part No.Straight
Thread
(U)
Pipe
Thread
(NPT)
Dimensions (mm)
A
(Min) 
B
(Min) 
C
(Min)
D
(Max)
E
(Max)
UMOS-0202U5/16-24-12.71516.82.35.6
UMOP-0202N-1/817.519.822.44.17.1
UMOS-0303U3/8-24-14.216.819.12.35.6
UMOS-0404U7/16-20-17.519.822.44.17.1
UMOP-0402N-1/817.519.822.44.17.1
UMOP-0404N-1/422.124.627.74.17.9
UMOS-0505U1/2-20-19.123.126.24.17.9
UMOS-0606U9/16-18-20.624.627.74.17.9
UMOP-0606N-3/825.429.533.34.18.6
UMOP-0608N-1/2313438.95.611.2
UMOS-0808U3/4-16-25.429.533.34.18.6
UMOP-0808N-1/2313438.95.611.2
UMOS-1212U1-1/16-12-35.838.944.55.612.7
UMOS-1616U1-5/16-12-42.945.251.65.614.2

How To Order

Fractional(Inch)Tube fittings 

UNILOK fractional(inch) size tube fittings are ordered by part number as shown below. 

Example: The following part number, UMC-0804N-SS, is designated for Male Connector, 1/2"OD x 1/4" Male NPT, 316SS.


U

MOP

-

08

04

N

-

SS

UNILOK
Tube Fittings

Fitting Type

Tube O.D.

Pipe Size

Thread Type

Material

NACE

Plating
Only for Brass &
Carbon Steel

 Fractional(inch) Tube Designation
Tube O.D.inch1/161/83/161/45/163/81/25/83/47/811-1/81-1/41-1/22
mm1.503.174.766.357.939.5212.7015.8819.0522.2225.4028.5731.7538.1050.80
Designator010203040506081012141618202432
Pipe Size DesignationMaterial Designation
Pipe Size1/81/43/81/23/411-1/41-1/22DesignatorMaterials
Designator020406081216202432SS316SS
BSBrass
Thread Type DesignationCSCarbon Steel
DesignatorThread TypeMOAlloy 400
NNPTNational Standard Pipe ThreadIN60Alloy 600
RISO 7/1Taper Pipe ThreadIN65Alloy 625
GISO 228/1Parallel Pipe ThreadIN85Alloy 825
USAE J1926Straight Thread BossHCAlloy C-276
SSAE J51437° FlaredTFPTFE
T Tube EndDPDuplex
None UNILOK PortSDSuper Duplex
6MO6MO/SMO254
NACE Application Plating Designation
None- NPNickel
NNACE Application BPBlack Phosporized

Tubing & Pipe end Thread Information

Tubing Information  

The proper selection of tubing is essential to assure maximum fitting reliability and performance. When choosing tubing material, size and wall thickness, consider system’s pressure, flow rate, temperature, environment and compatibility with great care. 


Maximum Allowable Working Pressure 

Stainless Steel Tubing 

Fully annealed and seamless stainless steel tubing to comply with ASTM A269 or equivalent. Hardness should not exceed Rb 80. Tubing should be free from scratched and suitable for bending and flaring. 


Fractional(Inch) Tubing
Tube O.D.
(inch)
Tube Wall Thickness (inch)
0.0280.0350.0490.0650.0830.0950.1090.1200.1340.1560.188
1/8855010950         
3/165500710010300        
1/441005200760010300   Working pressure in psig
5/16 410059008100       
3/8 335048506550       
1/2 2650375051506750      
5/8  2950405052506050     
3/4  24503350425049505850    
4/8  20502850365042504850    
1   24003100360042004700   
1-1/4    240028003300360041004900 
1-1/2     230027003000340040004900
2      20002200250029003600
Metric Tubing
Tube O.D.
(inch)
Tube Wall Thickness (inch)
0.81.01.21.52.02.22.53.03.54.04.5
39700          
4790011500         
645006100785010300   Working pressure in psig
8 450056507500       
10 3500435058008400      
12 2900360048006800      
14 23002900400055006250     
15 2002750365052005800     
16  24503350480053505800    
18  21502950420046505350    
20  20302600375042004800    
22  17502300335037504350    
25    2900335037504650   
38     203023002900350039004500
For gas service application, use only tubing with wall thickness on outside of gray areas.
Allowable stress of 20000 psig between -29°C(-20°F) and 37°C(100°F) based on ultimate tensile strength to be 74000 psig.


Copper Tubing 

Fully annealed and seamless stainless steel tubing to comply with ASTM B75 or equivalent. Hardness should not exceed Rb 60. 


Fractional(Inch) Tubing 

Tube O.D.
(inch)
Tube Wall Thickness (inch)
0.0280.0350.0490.0650.0830.0950.1090.120
1/41300160025003500    
3/8 100016002200    
1/2 800110016002200   
5/8  900120016001900  
3/4  7001000130015001800 
1  500700900110013001500


Metric Tubing 

Tube O.D.
(inch)
Tube Wall Thickness (inch)
1.01.52.02.53.0
623503670   
817102680Working pressure in psig 
1013502090   
12110017102350  
20 99013501710 
25 780106013501640

For gas service application, use only tubing with wall thickness on outside of gray areas. Allowable stress of 6000 psig between -29℃(-20℉) and 37℃ (100℉) based on ultim ate tensile strength to be 30000 psig. 


Monel Tubing 

Fully annealed and seamless stainless steel tubing to comply with ASTM B165 or equivalent. Hardness should not exceed Rockwell Rb 75. 


Fractional(Inch) Tubing 

Tube O.D.
(inch)
Tube Wall Thickness (inch)
0.0350.0490.0650.0830.0950.1090.120
1/4480070009500    
3/8310044006100 Working pressure in psig
1/2230032004400    
3/4 2200300040004600  
1  22002900340039004300

For gas service application, use only tubing with wall thickness on outside of gray areas. Allowable stress of 6000 psig between -29℃(-20℉) and 37℃ (100℉) based on ultimate tensile strength to be 30000 psig. 


Determination Factors of MAWP at High Temperature Application 

To determine allowable working pressure at elevated temperature, multiply allowable working pressure and factors which are shown in the table. 

TemperatureMaterials
316SSCopperMonel
901941.00.80.88
2003920.960.50.79
3105900.85-0.79
4808020.79-0.75
5369960.76--
64412270.37--

Example: 316SS Tubing, 1/2"ODx0.049"WT at 310℃ AWP: 3750 x 0.85 = 3187 psig.  

* MAWP: Maximum Allowable Working Pressure 

* AWP: Allowable Working Pressure  


Pipe End Thread Information 

The end connections with the lower pressure rating is the determining factor of pressure rating for the fittings with both UNILOK tube ends and pipe thread ends . 


Pressure Rating for Pipe End Thread 


Tapered Pipe Threads - NPT or ISO 7/1(BSPT)
Allowable pressure ratings for male and female threads are based on ASME B31.3 at ambient temperature.
ISO 228/1 Parallel Thread (BSPP)
The pressure ratings are at ambient temperature.
Pipe Size316SS316SSUNILOK
Desig nator
Male
Pipe Size
316SSUNILOK
Designator
MaleFemaleMaleFemalebarpsig
inchbarpsigbarpsigpsigbarpsig1/83154568-02G
1/1676011000460670055002303300-01N/R1/43154568-04G
1/869010000440650050002203200-02N/R3/83154568-06G
1/45508000450660040002203300-04N/R1/21602320-08G
3/85407800360530039001802600-06N/R
1/25307700330490038001602400-08N/R
3/45007300320460036001602300-12N/R
13705300300440026001502200-16N/R
1-1/44106000350500030001702500-20N/R
1-1/23405000310460025001502300-24N/R
22703900270390019001301900-32N/R


O-Seal Fittings 

Rated to 206 bar (3000 psig) for 316SS fittings up to 1 inch and 25mm 


Kinds of Pipe End Thread

NPT Pipe Thread
NPT (National Pipe Thread) is based on ANSI B1.20.1.

ISO 7/1 Tapered Pipe Thread
International Organization for Standard (ISO 7/1) Tapered (PT) Equivalent to BSPT (British Standard Pipe Taper Thread), DIN 2999, JIS B0203

    

ISO 228/1 Parallel Pipe Thread
International Organization for Standard (ISO 228/1) Parallel(PF) Equivalent to BSPP (British Standard Pipe Parallel Thread), DIN ISO228/1, JIS B0202 Gasket or O-ring is normally used to seal into the parallel female threaded components.

  

Features

Gaugeability

UNILOK tube fittings are produced with exact and tight tolerances. Without such close tolerances, proper interaction among the nut, ferrules, and body would not occur.


Corrosion Resistance

UNILOK ferrules have the strongest corrosion resistance due to our own special hardening process. 

This has been proven in various industrial areas over several decades.


Interchangeability

UNILOK tube fittings can be interchanged with tube fittings manufactured to international standards.


Less Torque and Anti-Distortion

When the nut is tightened, both ferrules are driven forward between the nut and the body. 

This axial movement doesn't transfer any torque from the fitting to the tubing when the original tubing's mechanical properties are maintained.




UNILOK Tube Fittings Installation Instruction 

닫기
top
로그인하셔야 본 서비스를 이용하실 수 있습니다.